null

Ruger 10/22 Takedown .22LR, 18.5" Barrel, Red/SS, 25rd

Pictures may not exactly represent this item. Please read the description before purchasing.
(No reviews yet) Write a Review
$439.00
   $399.89
(You save $39.11 )
Out of Stock
SKU:
736676111206
BRAND:
Manufacturer Number:
11120
Caliber:
22 Long Rifle
Model:
Ruger 10/22
Rounds:
25
Unit of Measure:
Each
Classification:
Firearm
the problems of jetting this is great worth reading Before changing jetting you should first check for any intake leaks. Carb cleaner works great but water will do. Start your quad or bike . Hold throttle at stead idol spay the intake if there is a spike in the RPM's, you will then need to fix the leak. Don't over torque the intake bolts it will warp, making the leak worse. make one change at a time . You think you did everything right. Bought the most expensive pipe. Paid extra for that jet kit. Followed all the instructions to the letter. If you were lucky, the machine just might actually perform better—except, of course, for that pesky off-idle stumble or the giant flat spot in the midrange, or how about the severe top end miss (must be the darn rev limiter!). Experience tells me that almost every hop-up anybody has ever done to an ATV has produced at least one point in the rev range that carburetion is considerably worse than stock. Why? Because all you have is a piece of paper that gives you recommended jetting settings. And unless you happen to be lucky enough to ride in those same conditions, there will be some point in the rev range where you will be too rich or too lean. WHAT IS JETTING Jetting is providing the engine with a combustible mixture. The ideal combustible mixture ratio is 14.7 parts of air to one part of fuel, with the most power being produced around 12-13:1. While a motor can (and will) operate on a mixture that is considerably richer or leaner, power output falls off. If you happen to go leaner and ride it hard, you may end up with an over-heated motor, or worse, a seizure. Also be aware that carburetion is measured at throttle position settings. It has nothing to do with engine rpm or transmission gears. So telling the pipe manufacturer or Boss that it skips in third. but not fifth gear is totally useless information. Did you know that your fuel pre-mix ratio (two-strokes only!) affects your jetting? A carburetor jet flows X amount of fuel and air at a given time. In that fuel is, say, 32 parts of fuel and 1 part of oil (32:1). If you change your pre-mix ratio to 20 to 1 because you are afraid of burning up your motor, all of a sudden the amount of fuel has been decreased by 37.5 percent. And since it is the fuel and NOT the oil that keeps your ring-ding cool, you run even leaner and hotter! Same theory applies to four-strokes as well; the more fuel entering the engine, the cooler the piston will be. The oil and water cooling systems are not designed to cool the piston; only the little bit of fuel that is mixed with the incoming air charge prevents your motor from seizing. ONLY after the heat has been transferred through the piston to the rings and then to the cylinder, will the cooling system get the chance to do its job. WHY DO I HAVE TO REJET? In a stock engine, the factory has spent a considerable amount of time and money trying various jets and needles to come up with jetting that not only passes the EPA (Environmental Protection Agency) regs, but allows the machine to be operated at roughly factory rated output without overheating and blowing up. When you, as an owner, change anything to do with the intake that would remove factory built-in restrictions to air flow into the engine or, exhaust changes that would do the same for air flow out of the engine, then you will need to rejet. Why? A carburetor is designed with fixed size main and slow (pilot) jets. The jet needle attached to the bottom of the slide is fixed at a certain height. Only the idle mixture screw is adjustable. If you have increased air flow as outlined above, the increased volume will still be mixed with the same amount of fuel as before, resulting in a lean mixture. If you replace the main jet with a larger numbered jet, the jet’s internal hole will be larger, thus flowing a greater quantity of fuel at 3/4-full throttle. If you raise the position of the slide’s jet needle by lowering the jet needle clip, you are allowing more fuel to rise out of the needle jet at a given part throttle position which is generally 1/4-3/4 open. If you replace the low speed (pilot) jet with a larger numbered jet, the internal hole will be larger, thus flowing more fuel at very small openings of 1/16-1/4 throttle. I STILL FEEL I CAN JET BETTER THAN THE FACTORY CAN Even if you popped for the extra expense of a jetting kit, don’t expect your jetting to be "spot on" unless you are willing to experiment and try different jets. Why? Say you install the main jet the jet kit recommends and it seems to run OK. Is it truly the best for your machine in your riding conditions? It may not be, unless you experiment by going up a jet size at a time until your machine exhibits a stumble at full throttle, indicating a too rich mixture. Then by dropping back one size you can be confident that now you have the correct jet for your machine in your riding conditions. The same thing should also be done with the other fixed jets of your carburetor (jet needle and slow speed pilot jet.). WORKING WITH INDIVIDUAL CARBURETOR CIRCUITS So, how do you start? At the bottom. Then you jump to the top and work your way down. IDLE MIXTURE SCREW: The idle mixture screw is the only externally adjustable carburetor jet available and controls up to 1/8 throttle only. There are two types of idle mixture screws. One type is called a fuel screw because it regulates the flow of fuel into the idle circuit. This type of screw is located ahead of the carb’s slide tower (motor side) and is most often found under the carb’s bore and upside-down directly ahead of the carb’s float bowl. By turning the screw out you increase the amount of fuel that is allowed to slip around the tapered needle and into the carb’s bore where it is mixed with air that has snuck under the carb’s slide. If the idle mixture adjustment screw is located behind the carb’s slide tower (airbox side) then the adjusting needle regulates air flow into a fixed flow of fuel intended for idle. By turning this screw inward you are reducing the air flow, thus richening the idle mixture. When the motor is up to operating temperature, set your idle speed screw to a stable idle. Then use either your idle fuel or air screw to obtain a stable idle. Reset the idle speed screw as necessary after obtaining the correct idle mixture. MAIN JET The main jet controls 3/4-full throttle only. Ideally you should start very rich (large numbered jet) and test at full throttle. It should skip. If not then you are not rich enough! Once you have your rich stumble, back off one size at a time until full throttle operation results in normal operation. (Note: If your ATV runs faster at 3/4 throttle than full throttle you are definitely lean on the main!) JET NEEDLE The slide’s jet needle controls 1/4-3/4 throttle. It does this by passing upward through the needle jet. The needle jet is a long brass tube that contains many small holes in its sides that air passes through. Fuel from the float bowl enters this air stream from the main jet and into the center of the needle jet where it mixes with the air to create an emulsion. This mixture of fuel and air is then metered by the height, taper and diameter of the jet needle as the emulsion passes upward around the jet needle into the carb’s bore where it mixes with still more air to (hopefully) arrive in the motor in a combustible fuel-to-air ratio. If you have a soft hesitation,
Manufacturer Ruger
Manufacturer Part # 11120
Model 10/22
Model Takedown
Action Semi-automatic
Caliber 22 LR
Barrel Length 18.5"
Color Silver
Accessories Ballistic Nylon Case
Type of Barrel Takedown
Capacity 25rd
Sights Adjustable Rear, Bead Front Sight
Subcategory Hunting Rifles
Finish Matte
Stock Synthetic
This purchase comes with the Impact Guns Lifetime Warranty  (Read More)

Estimated shipping times are posted on the product information page under the title "Ships On Or Before:" please note that all lead-times are estimates.  For items in our warehouse, we usually ship within 3 business days.  For items only available at distribution or other sources, the ship time may be up to 10 business days.  For items only available at the manufacturer, the lead-time may be a few weeks or longer-- depending on availability.

Please also note that some items are unique, hard to obtain, or one-of-a-kind, so Impact reserves the right to cancel your order should an item not be available to ship.

We will not charge your credit card until your product ships, except for certain special orders.

We normally will ship FedEx and US POSTAL. If you need faster shipment, we can ship 2nd Day or Next Day for an extra charge.

Alaska and Hawaii residents - your order MUST ship 2nd day or faster. Most orders over $100 value will ship with a signature-required to ensure they make it to you. Products that have free shipping only applies to the lower 48 states.

NOTE: We make every effort to get your order shipped as fast as possible. In some circumstances, especially during sales and after weekends, we may not get your order shipped in the time specified. Please rest assured that we will ship your item as soon as we can.

We want you to be satisfied with your purchase and offer the following simple return policies for your benefit.
Non-Returnable Items:

Due to safety, legal, and regulatory reasons, our return policy does not apply to the following items:

  • firearms (including any serialized items ex. lower receivers)
  • black-powder guns
  • optics
  • ammunition
  • gunpowder
  • primers

Also, if a firearm is not picked up from the destination dealer, the customer is responsible for the return shipping charges and a 6% restocking fee.

Firearms Lifetime Guarantee: Impact Guns offers a lifetime guarantee of firearms. We guarantee to replace or repair any defective firearm for the life of the original purchaser. For details, see our Lifetime Warranty Policy.

How do I start the return process?
  • Log in to your www.impactguns.com account and locate and click on the "Request Return" link.
  • An Impact Guns agent will review your request for a return and respond within two business days.
  • As an alternate method, you can send an email to sales@impactguns.com. Please be sure to include your original order number and relevant contact information.
When will I get my credit or return?
  • Most returns are fully refunded in 3-5 days after we receive and process the return. It may take longer for the credit to appear in your account depending on your bank. Most items that are in stock ship within 3-5 days after receipt of your returned item, but may take longer depending on availability.
What about damaged/incorrect items (not including non-returnable items listed above)?
  • If you received a damaged, defective, or incorrect item, Impact Guns will ship you a replacement of the exact item upon receipt of the damaged or defective item. Impact Guns will send you a return shipping label for the return.
What about return shipping costs?
  • If an Impact Guns error causes the need to return an item or we are replacing a returned defective or incorrect item, then we will pay the associated shipping costs.
  • Otherwise, the customer is responsible for any return shipping costs. When returning an item, please add package tracking and adequate insurance.